Samsung i9070 Boot reapir Success HERE

Samsung i9070 Boot reapir Success HERE

Model:

Success Repair done screen shot:

Samsung G900F (S5) Dead Boot repair done with files free here

Samsung G900F (S5) Dead Boot repair done with files free here

Model:

Download all of Requirements:

• Odin Dowanload HERE

• Boot Loader Files HERE

• MSM8974PRO_boot_recovery.pit Download from HERE

Procedure:

Note: If you have any get error while flashing blootloader in working mobile that means you have to must latest ver. Bootloader if you want to new create firmware bootloader from HERE

• Run Odin flasher Tools.

• Select: MSM8974PRO_boot_recovery.pit from the click on PIT button and

• Select: BL_G900Fxxxxxxxx_...tar from the Click on BL button and last

• Check in Odin flaher tools of T Flash option

• Insert Memory card working in Galaxy S5 SM-G900F mobile phone

• Download Mode in working Galaxy S5 SM-G900F mobile phone

• Attach mobile in computer via USB cable.

• Click on Start button when detect mobile in odin flasher tools

• After done flash, you will get files of PIT & Bootloader from the memory card

• Remove memory card in the working s5 mobile and insert in the dead s5 mobile.

• and Preess & hold vol. Down button + Home + Power button.

• If you have to successfully recovery process completed you will get Download mode in dead Galaxy S5 device.

• just flash device in multi firmware of Pit, Bootloader, AP, CP, And CSC files.

SDC Dead Boot Repair File inATF Box:

Requirements:

• ATF Box

• Memory card ( SD Card )

Procedure:

• Paste your SDC Files into: C:\AdvanceBox Turbo Flasher\sd_card\SDC_IMAGE\

• Create SDC file from the using SD Card in SDC Tools see Below picture

• After Process done insert SD Card in mobile

• Must your battery charged 80% up

• Hold volume Down button + home + power button to put Download Mode

Samsung Note 3 N900 Dead boot Repair Solution CPU: Samsung Exynos 5 Octa 5420 100% Tested

Samsung Note 3 N900 Dead boot Repair Solution CPU: Samsung Exynos 5 Octa 5420 100% Tested

Download SDC Images From Below

SM-N900 for Android 4.3

SM-N900 for Android 4.4.2

1 Put your Downloaded SDC Files into: C:\AdvanceBox Turbo Flasher\sd_card\SDC_IMAGE\

2 Create SD Card using SDC Tool from ATF Below image given

Disassemble phone to expose TP Area.

3. Insert SD Card.

4. Connect Power Supply or Battery.

5. Use TWEEZER TO SHORT that RESISTOR in TP PIX - (BE CAREFUL!! DO NOT DAMAGE RESISTOR!!)

PCB 1

PCB 2

6. Use VOLUME DOWN + HOME + POWER Button to make phone enter SD CARD MODE (You can also use JIG).

*** Once phone enter SD CARD MODE, DO NOT SHORT THE RESISTOR ANYMORE!!! ***

You will see something like blow given n the picture:

SDCARD MODE

UP KEY : NORMAL BOOTING

DOWN KEY : DOWNLOAD MODE <------------ Select this


Last Flash with ODIN PIT + BL + AP + CP and CSC Use multi file firmware (Repair firmware Download)

Samsung i9300 & N7100 Dead boot repair solution & imei null solution only for i9300

Samsung i9300 & N7100 Dead boot repair solution & imei null solution only for i9300

:: Procedure ::

* Download samsung s3 boot card maker Here

* Extract it on desktop

* Take a card reader insert memory card into the card reader and connect it to the pc

* From the extracted folder run Diskdump2.exe

* Select generic storage Device. pictures below follow it


* Now to write the scripts follow the below given picture

Now done your are succesfully created Dead boot memorycard

To continue further

:: Requerments ::

* Z3X samsung Box or SPT Box (i used z3x)

* special UART Cable (300k or 500k uartcable)

* Download teraterm-4.78 From Here

* Fully charged battery

Dead boot Reapairing procedure

* Download and extract teraterm-4.78 on desktop

* From extracted folder run ttermpro.exe there select serial port and change the serial port to z3x serial
port link below givin in the picture

* After Select The Serial Port Press Ok Button then Go To Setup Click Serial Port Option
Select Baud Rate 115200 Then Press Ok Button link below given in the picture

* Now insert the created boot card to the mobile

* Connect the Uart cable via z3x box

* Now Insert the battery and wait for 5min if the procces did not start disconnet the mobile close termpro agin try it.

* if it run success you will the result below given link this.

pit_check_integrity: invalid pit.(0x0)
pit_check_integrity: invalid pit.(0x0)
update_guid_partition_table: There is no pit binary.
fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
fsd_reclaim 1284: MST is not recognized
fsd_reclaim 1599: Error(nErr=0x0)
fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
j4fs_open 153: Error(nErr=0x40000000)
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: 'param.j4fs' does not exist, make new one..
j4fs_write_file_bootloader 184: j4fs panic
fail
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: debug level file does not exist..*INCORRECT!*
init_fuel_gauge: battery is not detected, do not init fuelgauge
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL2:0x3b
init_microusb_ic: MUIC: CONTROL2:0x3a
PMIC_ID = 0x2
PMIC_IRQSRC = 0x0
PMIC_STATUS1 = 0x10
PMIC_STATUS2 = 0x0
PMIC_PWRON = 0x2
PMIC_IRQ1 = 0x27
PMIC_IRQ2 = 0x0
s5p_check_keypad: keypad value=0x0
s5p_check_reboot_mode: INFORM3 = 0 ... skip
s5p_check_upload: MAGIC CODE=d1b0f038
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
s5p_check_download: update mode=0
j4fs_read_file_bootloader 355: j4fs panic
s5p_check_tzsw: invalid tzsw type! dummy?
scr_draw_image: draw 'download_error.jpg'...
j4fs_read_file_bootloader 355: j4fs panic
read_param_file: 'download_error.jpg' j4fs read failed!
fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
a2, 60, 90,

* if you get this error at the end [Patch Stop] This is not Rom Code. you can't fix your mobile you have to change your emmc chip

TN default
<OK>
<OK>
[DVFS] INT(1) : 0
DRAM Type : LPDDR2 8G
[DVFS] MIF(3) : 0
[EPLL][VPLL][CLK_DIV] OK
<OK>
[LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
[DVFS] ARM(0) : 5
[DVFS] INT(1) : 0
[DVFS] G3D(2) : 0
[DVFS] MIF(3) : 0
[SD_INIT
SDMMC_HighSpeedONE]
SD_READ: 20000 20000 0x40008000 -> 668484 usec
<OK>
Inp32(uAddr) : 0xea00007e
FW Booting
[Patch Stop] This is not Rom Code.

* After done this your mobile must me and download mode or white screen if white screen manually put into download mode.

* After dead boot repair mine white screen i manually put into download mode picture below

 * Now update your mobile with factory firmware with PIT file lik below given and the picture.Factory firmware Download Here

 * After update complete your mobile may not have imei .imei null or your mobile will not boot beacause of dead boot repair. your efs must be corrupted

* To Fix this problem first root your mobile Download from here (flash it through odin select as odin)

* Now Download this EfS repair file and flash it through odin select as odin your mobile must boot
but the imei become link this 004999010640000
I9300_Repair_efs.tar.rar

 * if your imei is null you can't repair using this box so 1st you have to repair the efs using above given file. if your imei become link this only (004999010640000) you can repair using z3x or other samsung tool

* Now follw the picture to repair imei problem.

* After IMEI Repair